Question I occasionally get the check engine light on my '04 Highlander. It goes away after a day and I've taken it to the dealership once for the problem - they asked if I recently filled the gas tank and did I "tighten" the gas cap. Well the
Well the check engine light has started to appear more frequently (and it always goes away within a day or two). I borrowed a code reader from a friend and the code being displayed is P2238.
I can find no meaning to that code except for a previous post you have that refers to a TSB EG034-04 (which I think was for a Camry).
2004 Prius service plug was disconnected now car won't start
he HV service plug was disconnected to weld on the car but now it wont start anymore. is there a procedure to reset something to get it started again?
It may need the Toyota Hand Held Scanner to reset? I am not sure. If DTC were set then you may need your Toyota dealer to help you. Use a flat bed to transfer the car.
I have heard of people w/the new model Prius not fully seating the interlock when replacing the safety plug. It is something like a lever that needs to be pushed down. Sorry not more specific, my Prius is previous gen and the plug is not the same. Please post the solution; we need these things in group memory.
* When the warning lamp is illuminated or the battery has been disconnected and reconnected, pressing the power switch may not start the system on the first attempt. If so, press the power switch again. * With the power switch’s power mode changed to ON (IG), disconnect the battery. If the key is not in the key slot during reconnection, DTC B2799 may be output.
US TSB EG019-05 May 13, 2005. NO "READY ON" AND/OR M.I.L. "ON" DTC P3140, P3141, OR P0A0D (SERVICE PLUG INSTALLATION). May occur if the service plug installation procedure isn't fully performed following a service that required removal of the HV service plug.
Toyota Repair - Immobilizer System Expert: Ted Ritter - 7/29/2008
Question Dear Ted Ritter,
I am working on 2007 TOYOTA FORTUNER (Model: TGN51-EKPSKV, Engine:2TR-FE). It’s equipped with engine immobilizer system. Unfortunately, the customer lost all keys; therefore, he bought a new Ignition key set (having the Master & Sub keys) and the transponder ECU.
To register the master and the sub keys to the immobilizer ECU, I used the scan tool, and tried to start the engine but it didn’t. By using scan tool I read Diagnostic Trouble Code (B 2799
Engine Immobilizer system). Therefore, I suspected that, there is no communication between the transponder ECU and the Engine ECU (ECM). Then I traced the related electrical wirings and I have tried several times to clear the DTC (B 2799) using scan tool and by disconnecting the negative clamp of the battery, but the code remains unclear.
From the DLC3 connector I have shorted TC-CG terminals for 30 minutes and longer to register the ECU communication ID. But in all these, I am unable to start the engine. What is your proposal? I am waiting for you assistance.
ダ・ヴィンチ・コード
http://blogs.yahoo.co.jp/bunchou2/36947634.html
生物の形を決める遺伝子スイッチ
http://blogs.yahoo.co.jp/attyonnblique/49428177.html
2010/10/16(土) 午後 6:51返信する
C1201
エンジン系統異常
C1201/98
1. Engine 回転中
2. Brake ブースタ圧がマニホールド圧より38kPa(285mmHg)以上高い
3.10秒以上
4.1トリップ
http://www.irsural.ru/caldina24x/x343/servinfo/x34300001kl000c.html
2010/10/16(土) 午後 7:21返信する
C1201/51:
C1201/51 Engine 回転数500r/min以上で Engine からの異常信号入力が5秒以上継続 Engine control コンピユータ
http://www.irsural.ru/caldina24x/x343/servinfo/x34300000p5000c.html
2010/10/16(土) 午後 7:24返信する
http://share.qclt.com/?悪田Toyota%20RAV4%20Repair%20Manual/Brake%20Control/Vehicle%20Stability%20Control%20System/0370016.pdf
http://highlanderclub.ru/files/manual/04/20zww400/c120151.pdf
2010/10/16(土) 午後 7:25返信する
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1
http://www.obd-codes.com/p0031
http://www.toyotapart.com/M.I.L._ON_DTC_P0031_AND_OR_P2238_T-EG032-04.pdf
2010/10/16(土) 午後 7:36返信する
P2238 OXYGEN SENSOR PUMPING CURRENT CIRCUIT LOW (FOR A/F ... - [ このページを訳す ]
ファイルタイプ: PDF/Adobe Acrobat - クイック ビュー
DTC Detection Condition. Trouble Area. P2238. A/F sensor (bank 1 sensor 1) circuit low. A/F sensor admittance is less than 0.022 1/Ω .... If DTC P2237, P2238, P2239, P2251, P2252 or P2253 is displayed, check the bank 1 sensor 1 circuit. ...
http://highlanderclub.ru/files/manual/04/21j6674h/cip2238.pdf
2010/10/16(土) 午後 7:39返信する
Toyota Repair - DTC Code P2238 - Highlander '04
Expert: Ted Ritter - 1/26/2006
Question
I occasionally get the check engine light on my '04 Highlander. It goes away after a day and I've taken it to the dealership once for the problem - they asked if I recently filled the gas tank and did I "tighten" the gas cap. Well the
http://en.allexperts.com/q/Toyota-Repair-832/DTC-Code-P2238-Highlander.htm
2010/10/16(土) 午後 7:41返信する
Well the check engine light has started to appear more frequently (and it always goes away within a day or two). I borrowed a code reader from a friend and the code being displayed is P2238.
I can find no meaning to that code except for a previous post you have that refers to a TSB EG034-04 (which I think was for a Camry).
http://en.allexperts.com/q/Toyota-Repair-832/DTC-Code-P2238-Highlander.htm
2010/10/16(土) 午後 7:43返信する
Should I be concerned about this code? Is there a TSB that deals with the Highlander for this type of engine code?
Thanks so much!
Get the answer below
http://en.allexperts.com/q/Toyota-Repair-832/DTC-Code-P2238-Highlander.htm
2010/10/16(土) 午後 7:44返信する
DTC B2620
Display Dimming Input Circuit
http://www.automotiveforums.com/t95876-dtc_chart_for_obd2.html
2010/10/16(土) 午後 7:47返信する
B2796 通信なし キー
トランスポンダキーアンプリファイア
ワイヤハーネスおよびコネクター
Engine control コンピュータ
http://www.irsural.ru/caldina24x/x343/servinfo/x34300001bo000c.html
2010/10/16(土) 午後 7:54返信する
B2799 Diagnostic Trouble Code Discussion for September 2010
Engine Immobilizer System Malfunction *
http://www.iatn.net/techmail/summaries/2010/09/B2799-dtc.html
2010/10/16(土) 午後 7:59返信する
DTC B2799 may be output.
2004 Prius service plug was disconnected now car won't start
he HV service plug was disconnected to weld on the car but now it wont start anymore. is there a procedure to reset something to get it started again?
It may need the Toyota Hand Held Scanner to reset? I am not sure. If DTC were set then you may need your Toyota dealer to help you. Use a flat bed to transfer the car.
http://priusonline.com/viewtopic.php?f=3&t=7844
2010/10/16(土) 午後 8:59返信する
I have heard of people w/the new model Prius not fully seating the interlock when replacing the safety plug. It is something like a lever that needs to be pushed down. Sorry not more specific, my Prius is previous gen and the plug is not the same. Please post the solution; we need these things in group memory.
DAS
3. NOTICE FOR HYBRID SYSTEM ACTIVATION
2010/10/16(土) 午後 9:02返信する
* When the warning lamp is illuminated or the battery has been disconnected and reconnected,
pressing the power switch may not start the system on the first attempt. If so, press the power
switch again.
* With the power switch’s power mode changed to ON (IG), disconnect the battery. If the key is
not in the key slot during reconnection, DTC B2799 may be output.
2010/10/16(土) 午後 9:02返信する
http://priusonline.com/download/file.php?id=682&sid=8266358455f452f0a0bed6647da05017&mode=view
http://priusonline.com/download/file.php?id=683&t=1&sid=8266358455f452f0a0bed6647da05017
2010/10/16(土) 午後 9:04返信する
P3140, P3141
http://autos.groups.yahoo.com/group/toy ... 019-05.zip
US TSB EG019-05
May 13, 2005. NO "READY ON" AND/OR M.I.L. "ON" DTC P3140, P3141, OR P0A0D (SERVICE PLUG INSTALLATION). May occur if the service plug installation procedure isn't fully performed following a service that required removal of the HV service plug.
2010/10/16(土) 午後 9:06返信する
Toyota Repair - Immobilizer System
Expert: Ted Ritter - 7/29/2008
Question
Dear Ted Ritter,
I am working on 2007 TOYOTA FORTUNER (Model: TGN51-EKPSKV, Engine:2TR-FE). It’s equipped with engine immobilizer system.
Unfortunately, the customer lost all keys; therefore, he bought a new Ignition key set (having the Master & Sub keys) and the transponder ECU.
http://en.allexperts.com/q/Toyota-Repair-832/2008/7/Immobilizer-System.htm
2010/10/16(土) 午後 9:21返信する
To register the master and the sub keys to the immobilizer ECU, I used the scan tool, and tried to start the engine but it didn’t.
By using scan tool I read Diagnostic Trouble Code (B 2799
2010/10/16(土) 午後 9:22返信する
Engine Immobilizer system). Therefore, I suspected that, there is no communication between the transponder ECU and the Engine ECU (ECM). Then I traced the related electrical wirings and I have tried several times to clear the DTC (B 2799) using scan tool and by disconnecting the negative clamp of the battery, but the code remains unclear.
2010/10/16(土) 午後 9:23返信する
From the DLC3 connector I have shorted TC-CG terminals for 30 minutes and longer to register the ECU communication ID. But in all these, I am unable to start the engine.
What is your proposal? I am waiting for you assistance.
Regards,
2010/10/16(土) 午後 9:23返信する
UCF20:VSC:TRC:ABS:
セルシオのチェックランプについて。知識が豊富なかたよろしくおねがいしますm(__)m今晩中にしりたいです。
平成10ねん20後期セルシオがBユーロ
先ほど三日ぶりにエンジンをかけたところ
走りだそうとブレーキを踏んだところ
ブレーキランプが点灯せず、あれっ!?
と、思い何度か踏みましたがつきません。するとパーキングからギアが動かず
あたふたしてたら
センター表示板にVSCと表示されその左側に赤のLEDが点灯、右下にTRC OFF と ABSの警告灯が点灯しました。
エンジンはかかるのですが走れません。
http://detail.chiebukuro.yahoo.co.jp/qa/question_detail/q1443009119
いったいなんなんでしょうか?
2010/10/18(月) 午後 3:47返信する
http://www.jikencenter.co.jp/publication/jkc_pdf/jkc2005_09.pdf
2010/10/18(月) 午後 3:51返信する
20後期セルシオなんですがバッテリーを外し、セキュリティ、社外ナビ、アンプ等々、相当な取り外し作業を行いました。
バッテリーを繋ぎセルをまわすとセルはまわりますがエンジンがかからず
VSCとTRCがついてしまいました。
あらゆる部分を外していたので1つづつ点検は難しいので考えられる場所があれば教えてください。
確認できている不具合はVSCが点きエンジンがかからない。
メーターのシフト表示が表示されない。
マルチのオーディオのみ使用できない。
外部気温が表示されない。です。よろしくお願いします。
補足
回答ありがとうございます。
VSCは点滅ではなく点灯しています。
バッテリーを外したあとと同じ現象です。
ただ、その後消えずに点きっ放しのままです。
http://detail.chiebukuro.yahoo.co.jp/qa/question_detail/q1219405977
2010/10/18(月) 午後 3:56返信する
トラックバック先の記事