Temporarily tighten the water pump pulley mounting bolts. Then, tighten them to the specified torque after the installation of alternator and others belt. Tightening torque: 9.0 ± 1.0 N·m
1.Remove the stopper of the fuel high-pressure hose.
2.Raise the retainer of the fuel high-pressure hose and pull out the fuel high-pressure hose in the direction shown in the figure. note If the retainer is released, install it securely after removing the fuel high-pressure hose.
caution After connecting the fuel high-pressure hose, slightly pull it in the pull-out direction to check that it is installed firmly. In addition, check that there is approximately 1 mm play. After the check, install the stopper securely.
4B10
Total displacement mL
1,798
Bore × Stroke mm
86.0 × 77.4
Compression ratio
10.5
Compression chamber
Pentroof
Camshaft arrangement
DOHC
Number of valve
Intake
8
Exhaust
8
Valve timing
Intake opening
BTDC 3° - BTDC 28°
Intake closing
ABDC 45° - ABDC 20°
Exhaust opening
BBDC 39°
Exhaust closing
ATDC 5°
Fuel system
Electronically controlled multipoint fuel injection
http://mmc-autoelectric.org.ua/manuals/eur/lancer_sportback/2012/index_M1.htm
2017/12/7(木) 午前 11:29[ ogw*og*3 ]返信する
Tighten the engine oil pan mounting bolts to the specified torque.
Tightening torque:
M6: 10 ± 2 N·m
M8: 31 ± 2 N·m
http://mmc-autoelectric.org.ua/manuals/eur/lancer_sportback/2012/index_M1.htm
2017/12/7(木) 午前 11:39[ ogw*og*3 ]返信する
WATER PUMP PULLEY INSTALLATION
Temporarily tighten the water pump pulley mounting bolts. Then, tighten them to the specified torque after the installation of alternator and others belt.
Tightening torque: 9.0 ± 1.0 N·m
http://mmc-autoelectric.org.ua/manuals/eur/lancer_sportback/2012/index_M1.htm
2017/12/7(木) 午前 11:47[ ogw*og*3 ]返信する
FUEL HIGH-PRESSURE HOSE DISCONNECTION
1.Remove the stopper of the fuel high-pressure hose.
2.Raise the retainer of the fuel high-pressure hose and pull out the fuel high-pressure hose in the direction shown in the figure.
note If the retainer is released, install it securely after removing the fuel high-pressure hose.
http://mmc-autoelectric.org.ua/manuals/eur/lancer_sportback/2012/index_M1.htm
2017/12/7(木) 午前 11:52[ ogw*og*3 ]返信する
FUEL HIGH-PRESSURE HOSE CONNECTION
caution After connecting the fuel high-pressure hose, slightly pull it in the pull-out direction to check that it is installed firmly. In addition, check that there is approximately 1 mm play. After the check, install the stopper securely.
2017/12/7(木) 午前 11:58[ ogw*og*3 ]返信する
燃料高圧ホース接続
燃料高圧ホースを接続した後、引き抜き方向に少し引いて、しっかりと取り付けられていることを確認してください。また、約1mmの遊びがあることを確認してください。点検後、ストッパーを確実に取り付けてください。
2017/12/7(木) 午後 0:01[ ogw*og*3 ]返信する