HO:JG1:S07A:N-ONE:ENG:MIL on:DTC:P0341:P0141:O2sensor:TSM:
[10]
P0341 Honda - Camshaft Position Sensor Incorrect Phase Detected
Read more: http://engine-codes.com/p0341_honda.html#ixzz2kqIhyyhH
P0341 カムシャフト・ポジション・センサー回路の範囲/機能不良
P0141 Honda - O2 Sensor 1 Sensor 2 Heater Circuit Malfunction Bank
Read more: http://engine-codes.com/p0141_honda.html#ixzz2kqJ9CDVy
P0141 ラムダ・センサー・ヒーター回路の異常(バンク1、センサー2)
P0341 カムポジションセンサー 測定-機能不良
http://jobd.jp/documents/3031JPBManual0909.pdf
http://www.audi-s.net/tips/BOOK/PDF/obd_dtc.pdf
2013/11/17(日) 午前 5:39返信する
Camshaft Position Sensor "A" Circuit Range/Performance
What does this mean?
OBD Code P0341refers to
This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor.
2013/11/17(日) 午前 5:45返信する
This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
2013/11/17(日) 午前 5:45返信する
Symptoms
Possible sumptoms of OBD code P0341
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition
2013/11/17(日) 午前 5:47返信する
Causes
Possible causes of OBD code P0341
A code P0341 may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel
2013/11/17(日) 午前 5:48返信する
Possible Solutions
Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following: Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks,
2013/11/17(日) 午前 5:51返信する
discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340
Related Codes
P0340 P0342
2013/11/17(日) 午前 5:52返信する
DTC P0141: Secondary HO2S (Sensor 2) Heater Circuit Malfunction
DTC Troubleshooting: P0141 (65)
http://arlequinlover.free.fr/Manuel%20Honda%20Civic/A00/HTML/30/SMG6E30K72100090141FAAT00.HTML
2013/11/17(日) 午前 6:44返信する
P0339: クランク センサ ノイズ
C:\Documents and Settings\user\My Documents\HO\N-box\DTC-AD1-90015\SYS\A000047_jpn
2013/11/17(日) 午前 8:40返信する
P0340: VTC カム センサパルスなし
C:\Documents and Settings\user\My Documents\HO\N-box\DTC-AD1-90015\SYS\A000061_jpn
2013/11/17(日) 午前 8:41返信する
トラックバック先の記事
全92ページ
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10]