SU:EBD-DA64V,K6A:ENG:power down:DTC:無:STFT:値想定外:O2sensor:WAT:

SU:EBD-DA64V,K6A:ENG:power down:DTC:無:STFT:値想定外:O2sensor:WAT:

[12]

イメージ 1

SU:EBD-DA64V,K6A:power down:DTC:無:STFT:値想定外:O2sensor:WAT:

暖気後走行に不満足
発進で失速気味、スムーズに加速できない。
エンジンも不安定、回転が変動


部品が間に合わないので、応急対応で端子の組み換え

一番リスクの少ないヒーター回路を組み換え次に
O2sensor系と判断した、青と白を組み換え、次に
残りを組み換えて、試運転してみる。

STFTの値とO2sensorの値など想定内に戻っているようだ。
実走行でも、状態は大きく改善されているようだ。
さらに、実走行などで状態を確認するようだ。

 

 

 

 

f:id:TAS-net:20191024235054p:plain

 

 

 

コメント(23)

     

顔アイコン

[PDF]
Oscilloscope waveform Types and interpretation - VASA
www.vasa.org.au/.../Oscilloscope_waveforms_introduc...

\Measure supply and ground voltages of that specific ECM and Capture waveforms (of suspect component). 9. Keep customer informed of ...... 
http://www.vasa.org.au/wp-content/uploads/2012/05/Oscilloscope_waveforms_introduction.pdf削除

2013/9/25(水) 午後 6:24ogw*og*2返信する

     

顔アイコン

Suzuki Vitara – good scope pattern. Scope patterns ... oxygen sensor at 450mv (is not oscillating) as it warms up. –enters closed loop and begins to oscillate. Engine in closed loop.削除

2013/9/25(水) 午後 6:24ogw*og*2返信する

     

顔アイコン

[PDF]
Cushman (with Suzuki engine) Service Manual.pdf - Silly Little Cars
sillylittlecars.com/.../Cushman%20(with%20Suzuki%2...このページを訳す
WITH 660 SUZUKI EFI ENGINE. MODEL .... removed and a sine wave signal such as a crank angle signal is ..... The electromotive voltage of the O2 sensor becomes high (about 1 V) when the air/fuel ratio is richer than its optimum value, and ...


http://sillylittlecars.com/files/Cushman%20(with%20Suzuki%20engine)%20Service%20Manual.pdf削除

2013/9/25(水) 午後 6:35ogw*og*2返信する

     

顔アイコン

Denso Oxygen Sensor Wiring - B2B Marketplace for Global Buyer ...
www.ecwhen.com/denso-oxygen-sensor-wiring_0このページを訳す
17489 products - Here you can find the latest products in different kinds of denso oxygen sensor wiring! ... CHEVROLET GMC ISUZU SUZUKI car brand Oxygen sensor,lambda sensor for CHEVROLET GMC ISUZU SUZUKI application; Taiwan.削除

2013/9/25(水) 午後 6:53ogw*og*2返信する

     

顔アイコン

With the engine idling, the sensor voltage should be cycling from low voltage to high voltage. The signal from most O2 sensors varies between 0 and 1 volt.
If the voltage is continually high, the air/fuel ratio may be rich or the sensor may be contaminated by RTV sealant, antifreeze, or lead from leaded gasoline.削除

2013/9/25(水) 午後 8:27ogw*og*2返信する

     

顔アイコン

When the O2 sensor voltage is continually low, the air/fuel ratio may be lean, the sensor may be defective, or the wire between the sensor and the computer may have a high-resistance problem.
If the O2 sensor voltage signal remains in a mid-range position, the computer may be in open loop or the sensor may be defective.削除

2013/9/25(水) 午後 8:32ogw*og*2返信する

     

顔アイコン

The sensor can also be tested after it is removed from the exhaust manifold.
Connect the voltmeter between the sensor wire and the case of the sensor.
Using a propane torch, heat the sensor element. The propane flame keeps the oxygen in the air away from the sensor element, causing the sensor to produce voltage.
While the sensor element is in the flame, the voltage should be nearly 1 volt.削除

2013/9/25(水) 午後 8:33ogw*og*2返信する

     

顔アイコン

The voltage should drop to zero immediately when the flame is removed from the sensor.
If the sensor does not produce the specified voltage or if the sensor does not quickly respond to the change, it should be replaced.
If a defect in the O2 sensor signal wire is suspected, backprobe the sensor signal wire at the computer and connect a digital voltmeter from the signal wire to ground with the engine idling.削除

2013/9/25(水) 午後 8:34ogw*og*2返信する

     

顔アイコン

The difference between the voltage readings at the sensor and at the computer should not exceed the vehicle manufacturer's specifications. A typical specification for voltage drop across the average sensor wire is 0.02 volt.
Now check the sensor's ground.
With the engine idling, connect the voltmeter from the sensor case to the sensor ground wire on the computer. Typically, the maximum allowable voltage drop across the sensor ground circuit is 0.02 volt.削除

2013/9/25(水) 午後 8:35ogw*og*2返信する

     

顔アイコン

Always use the vehicle manufacturer's specifications. If the voltage drop across the sensor ground exceeds specifications, repair the ground wire or the sensor ground in the exhaust manifold.
Most late-model engines are fitted with heated O2 sensors.削除

2013/9/25(水) 午後 8:36ogw*og*2返信する

     

顔アイコン

If the O2 sensor heater is not working, the sensor warm-up time is extended and the computer stays in open loop longer. In this mode, the computer supplies a richer air/fuel ratio. As a result, the engine's emissions are high and its fuel economy is reduced.
To test the heater circuit, disconnect the O2 sensor connector and connect a voltmeter between the heater voltage supply wire and ground.削除

2013/9/25(水) 午後 8:37ogw*og*2返信する

     

顔アイコン

With the ignition switch on, 12 volts should be supplied on this wire. If the voltage is less than 12 volts, repair the fuse in this voltage supply wire or the wire itself.
With the O2 sensor wire disconnected, connect an ohmmeter across the heater terminals in the sensor connector.
If the heater does not have the specified resistance, replace the sensor.削除

2013/9/25(水) 午後 8:39ogw*og*2返信する

     

顔アイコン

GRIDの空燃比計をつけて確認したところ、原因がわかりました。 

フィードバック領域内での走行中はきちんと14.6~14.7付近をキープしているので問題は 

ありませんが、信号などで停止してアイドリング状態になると、本来は同じく14.6~14.7付近 

でなければならない空燃比が、12~13付近をずっとウロウロしているのです。 

この状態がある程度の時間続くと、次の発進のときに加速が重くなるわけです。

http://www.geocities.co.jp/MotorCity-Rally/1407/o2s/削除

2013/10/3(木) 午後 7:18ogw*og*2返信する

     

顔アイコン

O2センサ信号系異常 - 今月の実践!整備事例
www.jaspa-oita.or.jp/jissen/2005/07/page2_1.html

今月は、先月号でも紹介した「O2センサ信号系異常」と同じ症状のトラブル事例を紹介する。 車は平成12年式プラッツ(車両型式GH-NCP12、エンジン型式1NZ-FE)で、高速道路を走行中にチェックエンジンランプが点灯したということで入庫。チェックエンジン ...削除

2013/10/3(木) 午後 7:21ogw*og*2返信する

     

顔アイコン

PACデバイス 製造元 ウォーカー社:1946年創業。本社、米国カリフォルニア。燃料系統及びエンジンコントロール装置製造・組立て会社。独立資本では世界最大規模。主要取り扱い商材はインジェクターキット、O2、MAP、EGRポジション・カムポジションなどのセンサー類。OEMスペックを満たす品質・性能をもつパーツを世界主要市場で販売しています。
センサー部分を主要純正センサーメーカーから調達しているので品質は純正と同等です。適応品番が多い。

http://www.syaken-parts.com/index.php?O2%E3%82%BB%E3%83%B3%E3%82%B5%E3%83%BC削除

2013/10/4(金) 午前 4:40ogw*og*2返信する

     

顔アイコン

PAC deviceトップページ > 会社概要
会社概要 
社 名
ピーエーシーデバイス株式会社
所 在 地
〒257-0052
神奈川県秦野市上今川町2-1
TEL 0463-84-3707 FAX 0463-74-5228
設 立
平成21年3月24日
代 表 者
神部 典之
事業内容
オートモーティブパーツ・アクセサリー・ケミカル商材卸売

http://www.pac-device.com/company.html

http://www.walkerproducts.com/products/oxygen-sensors/削除

2013/10/4(金) 午前 4:53ogw*og*2返信する

     

顔アイコン

Identify Oxygen Sensor Damage and Contamination

New Oxygen Sensor with no defects.


Oxygen Sensor damaged through contamination by antifreeze.


Oxygen Sensor that has been damaged by a rich fuel mixture.


Oxygen Sensor that has been damaged by silicone poisoning.


Oxygen sensor that has been damaged by lead poisoning.

http://www.walkerproducts.com/resources/technical-support/common-oxygen-sensor-conditions/削除

2013/10/4(金) 午前 4:55ogw*og*2返信する

     

顔アイコン

Bosch Oxygen Sensors
www.boschautoparts.com/oxygensensors/.../oxygensen...
このページを訳す
Bosch invented the automotive oxygen sensor and is the number one choice of vehicle manufacturers around the world. ... Where to Buy. Search for US locations near you that sell Bosch automotive products.削除

2013/10/4(金) 午前 5:01ogw*og*2返信する

     

顔アイコン

NTK Oxygen Sensors - NGK
www.ngksparkplugs.com › Products › Oxygen Sensors
このページを訳す
Suppliers and manufacturer of Spark Plugs, Oxygen Sensors, and performance products for automotive, motorcycle, commercial, marine, truck and lawn and garden applications. ... Each NTK Oxygen Sensor is: Extensively Tested During ...削除

2013/10/4(金) 午前 5:01ogw*og*2返信する

     

顔アイコン

Oxygen Sensors | DENSO Auto Parts
www.densoautoparts.com/oxygen-af.../oxygen-sensors
このページを訳す
Oxygen sensors, also known as Lambda sensors or O2 sensors among some vehicle manufacturers, are among the most ... The DENSO oxygen sensor catalog offers one of the most complete product lines in the industry, from Acura to Volvo.削除

2013/10/4(金) 午前 5:03ogw*og*2返信する

     

顔アイコン

ランシー

広州大酒店の自動車部品の共同。、 株式会社

Tel: 86-020-29056088

暴徒: 86-13570259339

スカイプ: ランシー。 shel

E- メール: chkkty( で) aliyun。 com

ウェブ: www。 gztycar。 com


http://japanese.alibaba.com/product-gs/car-sensor-made-in-china-md362290-for-mitsubishi-v31-v33-o2-814841696.html削除

2013/10/4(金) 午前 5:09ogw*og*2返信する

     

顔アイコン

Guangzhou Tianyu Auto Parts Co., Ltd. 






広州大酒店の自動車のコンポーネントの共同。、 株式会社。 自動車用電気部品に特化してい。 継続的な努力の年後、 我々へと発展しているマルチ- ブランド、 マルチ- 品種、 低い- コストと高- 品質のエンタープライズ。 当社は、 主にの広い範囲に従事していると他のスイッチウィンドウスイッチ、 efiシステム、 各種センサ、 リレー、 等。 主なブランドは、 デンソー、 アイサン、 東シナ海を物理化学的tokairika、 日立、 三菱、 trw上海、 パナソニックモトローラジーメンス、 デルファイ、 マレリ、 アイシンと。

http://japanese.alibaba.com/gs-suppliers_chkkty削除

2013/10/4(金) 午前 5:12ogw*og*2返信する

 

 

トラックバックされた記事

    
3CC:排気ガス浄化触媒:劣化;判断:MA:DTC:P0

3CC:排気ガス浄化触媒:劣化;判断:MA: 車検、点検でCO,HCが基準を超している場合がある。 その場合、一度触媒を活性化を試みるとよい。 その結果、排ガスのレベルが下がらない場合劣化傾向も疑ってもよい。 総合的に判断するには、関連データの傾向も材料にすることになる。 前提は、全てに共通の、基本点検が適切に機能していること。 O2sensor,A/Fsensorが想定の反応していること。 Rear O2senorの挙動がどうか? 前側のセンサと 削除

2016/12/9(金) 午前 1:35 [ CQF ]

トラックバック先の記事